Open 7 days · 7:00 AM – 11:00 PM

Whirlpool · Nepean & Stittsville

Whirlpool appliance
repair

Whirlpool builds machines that are meant to be opened, and its parts are the easiest to get hold of in Ottawa. That combination is why Whirlpool jobs are the ones most likely to be finished on the first visit rather than the second.

Technician repairing a Whirlpool washer in a customer's home

Diagnosis

On site, never over the phone

Warranty

90 days on every repair

Hours

7 days · 7 AM – 11 PM

What we fix

Whirlpool machines we take on

Whirlpool fits out a lot of builder kitchens in both our areas, so these are the machines the vans are stocked for by default.

Whirlpool refrigerators

Side-by-side and French-door models. Start relays, defrost timers and ice makers that stop filling.

Whirlpool washers

Cabrio and front-load machines. Drain pumps, lid locks and rotor position sensors carry most of the faults.

Whirlpool dryers

Belts, rollers, elements and the airflow faults that show up as AF long before anything breaks.

Whirlpool dishwashers

Seized chopper blades, packed sumps, heating faults behind a blinking clean light.

Whirlpool ovens

Bake elements, oven sensors and thermal fuses that blow during a self-clean cycle.

Whirlpool stoves & cooktops

Coil and glass tops, gas igniters that click without lighting, switches that stick on high.

Error codes

What your Whirlpool is trying to say

Whirlpool codes come in two halves: F is the system, E is the failure inside it. Once you know that, F8 E1 is always about water arriving and F9 E1 is always about water leaving.

One of these is not a fault at all. It is marked.

F21 / F9 E1
Draining took longer than the machine allows.
Filter, drain hose, then the pump. On older models the pressure hose is worth checking too.
F8 E1 / LF
Water is not arriving fast enough to fill.
A supply valve only half open, blocked screens in the hose ends, or a failed inlet valve.
F5 E2
The door lock will not engage.
The lock assembly. Once it starts failing intermittently it rarely recovers on its own.
F7 E1
The motor cannot reach the speed it was asked for.
Rotor position sensor first, drive belt second, motor last.
F6 E2
The control board and the motor board stopped talking.
Usually a corroded harness connector at the machine control, not the board itself.
AF
Airflow is restricted — dryers.
Lint screen first, then the whole vent run out to the outside wall.
Clean light ×7
Dishwasher heating fault, shown as seven blinks.
The heating element or the high-limit thermostat under the tub.
PF
Not a fault. The power was cut partway through a cycle. No visit needed
Press start to carry on. If it keeps happening, the outlet or the cord is worth looking at.

A code narrows the search — it does not price the job. We confirm the fault with the appliance in front of us before quoting anything.

Service area

Where we bring Whirlpool parts

Two areas, seven days a week. Whirlpool parts are the easiest to source in Ottawa, so first-visit fixes are most common on this badge.

Recent jobs

Three Whirlpool calls, start to finish

Real visits from the last few months. Prices vary by model and by what the diagnosis turns up, but the range is honest.

Whirlpool washer drain pump replacement

Top loader stuck full of water

Longfields · WTW5000DW

The problem

F21 at the end of every wash and a lid that stayed locked with the load inside.

What we did

Drain pump had a cracked impeller. Fitted a new pump, cleared the hose, and ran three drain cycles before signing off.

$245

Parts and labour

Whirlpool dishwasher sump cleaning and seal replacement

Dishwasher leaving everything gritty

Bells Corners · WDT750SAHZ

The problem

No error code, just a low hum and dishes coming out worse than they went in.

What we did

Chopper blade had seized and the sump was packed solid. Cleaned it out and replaced the wash impeller seal.

$210

Parts and labour

Whirlpool refrigerator start relay replacement

Fridge cycling every few minutes

Fairwinds · WRF535SWHZ

The problem

Compressor starting and stopping every few minutes, freezer going soft by the afternoon.

What we did

Failed start relay and overload. Replaced both, then checked the compressor amp draw to be sure it had survived.

$225

Parts and labour

About these prices. Each figure covers one specific repair on one specific model, on the day we did it. It is not a price list. What your own appliance costs depends on the fault, the model and the parts it needs, and we can only set that after seeing it — which is why we never quote over the phone.

Book a repair

Book a Whirlpool technician

Leave your details and we'll call back to arrange a visit. Include the model number and the code on the display — nine times out of ten that is enough to load the right part before the technician sets off.

Open 7 days · 7:00 AM – 11:00 PM
In-home service · 90-day warranty on every repair
We price the job after seeing the appliance, and the diagnostic isn't charged when you go ahead with the repair.